Contact Us






    Go Back

    Modular Actuators

    Features & Benefits

    – Integral housing flange engineered for NEMA 56 frame motor. C-face mounting.
    (NEMA 42 and 48 and IEC71 frame motor C-face mounting options available).
    – Rated loads to 8896N, depending on actuator gear ratio and motor horsepower.
    – Lift speeds to 4318mm per minute (varied with load and kw/rpm of motor).
    – Standard travel up to 608mm. (consult Duff Norton Australia for longer travel options).
    – Can be tandem-coupled for synchronous operation.
    – Optional motors, limit switches and position indicating transducer.
    – Clevis attachment accessories available for mounting eye bracket, clevis bracket and pivot pin.

    (ROTATING MACHINE SCREW MODELS)

    – Integral 56 frame, C-face mounting flange or IEC71.
    – Three-piece flexible coupling for easy motor assembly (included).
    – Four threaded holes in base for standard hydraulic cylinder, clevis end accessory attachment. Tapped 1/2 20 UNF-2B.
    – Rolled thread lifting screw, with work hardened finish, reduces coefficient of friction between screw and lifting nut. Provides smooth, efficient operation and long service.
    – Steel worm and bronze gear set for quiet operation. Available in 5:1 and 20:1 ratios.
    – Rugged, lightweight aluminum housing is corrosion resistant.
    – Bronze lifting nut for longer life.
    – Standard grease fitting on housing for easy lubrication of worm gear.
    – Stop-pin at end of lifting screw prevents inadvertent run-off of lifting nut.

     

    (TRANSLATING TUBE MACHINE SCREW MODELS)

    – Outer aluminum tube is corrosion-resistant and protects translating tube, lifting screw and nut.
    – Wiper-scraper seal in end of outer tube keeps dirt out and lubricants in.
    – Bronze guide bushing inside of outer tube reduces lateral movement of translating screw.
    – Translating tube zinc coated for weather-resistance.
    – Single or double lead lifting screw and nut for high efficiency and long wear.
    – Vent in outer tube prevents pressure build-up in the actuator
    – Furnished with standard clevis end on translating tube.
    – Threaded end is available; and on special order, depending on application, any type of threaded
    connection may be substituted.

     

    (ROTATING BALL SCREW MODELS)

    – Integral 56 frame, C-face mounting flange.
    – Three-piece flexible coupling for easy motor assembly (included).
    – Four threaded holes in base for standard hydraulic cylinder, clevis end accessory attachment.
    Tapped 1/2 20 UNF-2B.
    – Ball-bearing type screw and mating nut with rolling contact reduces friction to a minimum providing
    capability for higher speed and longer life with less power requirement.
    – Steel worm and bronze gear set for quiet operation. Available in 5:1 and 20:1 ratios.
    – Rugged, lightweight aluminum housing is corrosion resistant.
    – Bronze lifting nut for longer life.
    – Standard grease fitting on housing for easy lubrication of worm gear.
    – Stop-pin at end of lifting screw prevents inadvertent run-off of lifting nut.

     

    (TRANSLATING TUBE BALL SCREW MODELS)

    – Outer aluminum tube is corrosion-resistant and protects translating tube, lifting screw and nut.
    – Wiper-scraper seal in end of outer tube keeps dirt out and lubricants in.
    – Bronze guide bushing inside of outer tube reduces lateral movement of translating screw.
    – Translating tube zinc coated for weather-resistance.
    – Single or quadruple lead ball-bearing type lifting screw and nut for higher efficiency and long life.
    – Vent in outer tube prevents pressure build-up in the actuator
    – Furnished with standard clevis end on translating tube. Threaded end is available; and on special
    order, depending on application, any type of threaded connection may be substituted.